What Is The Effect After The Command No Access List 10 Is Entered?

What is correct in relation to NAT for IPv6 group of answer choices?

What is correct in relation to NAT for IPv6.

It is a temporary mechanism to assist in the migration from IPv4 to IPv6.

NAT for IPv6 is a temporary measure to aid in the move from IPv4 to IPv6.

Dynamic NAT provides a dynamic mapping of inside local to inside global IP addresses..

When would a network administrator use the clear access-list counters command?

When would a network administrator use the clear access-list counters command?when obtaining a baseline.when buffer memory is low.when an ACE is deleted from an ACL.when troubleshooting an ACL and needing to know how many packets matched.Jul 16, 2020

What is the effect of configuring an ACL with only places that deny traffic?

What is the effect of configuring an ACL with only ACEs that deny traffic? The ACL will permit any traffic that is not specifically denied. The ACL will block all traffic. The ACL must be applied inbound only.

What is the quickest way to remove a single ace?

What is the quickest way to remove a single ACE from a named ACL?Use the no keyword and the sequence number of the ACE to be removed.Copy the ACL into a text editor, remove the ACE, then copy the ACL back into the router.Create a new ACL with a different number and apply the new ACL to the router interface.More items…•Mar 11, 2020

Which 3 statements are generally considered to be best Practises in the placement of ACLs?

Place standard ACLs close to the destination IP address of the traffic. Place standard ACLs close to the source IP address of the traffic. Place extended ACLs close to the destination IP address of the traffic. Place extended ACLs close to the source IP address of the traffic.

Which type of ACL should be placed as close to the source as possible?

Standard ACLs should be placed as close to the destination as possible so they do not block traffic you do not wish to block. Extended ACLs should be placed as close to the source as possible.

What command would you use to remove this entire ACL command below ACL?

To remove the ACL, the global configuration no access-list command is used. Use the show access-list command to verify the removal of the ACL. To remove an ACL from an interface, first enter the no ip access-group command on the interface, and then enter the global no access-list command to remove the entire ACL.

What is the range of the IP addresses affected by the ACL statement?

The range covers 256 IP addresses, 0 to 255 for that subnet. A shorter range is shown in the third statement, which permits 128 IP addresses from the 172.16. 2.0 subnet (0-127). The final statement in the ACL gives an implicit deny to all IP addresses.

Which command is used to determine if an IP access list is enabled on a particular interface?

Answer: The show ip interface command is used to determine if an IP access list is enabled on a particular interface. Answer: The show ip interface command will show you if any outbound or inbound interfaces have an access list set.

Where should the administrator place this ACL for the most efficient use of network resources?

Place standard ACLs close to the destination IP address of the traffic. Place standard ACLs close to the source IP address of the traffic.

What is the next step in the troubleshooting process after a solution has been implemented on a laptop?

What is the next step in the troubleshooting process after a solution has been implemented on a laptop?Verify the solution.Document the solution.Ask the customer to explain the problem.Return the device to the customer. Explanation:Mar 29, 2016

Which command will configure a standard ACL?

The command syntax of a standard ACL is as follows: router(config)#access-list access-list-number {permit | deny} {source [source-wildcard] | host hostname | any}

Which scenario would cause an ACL misconfiguration and deny all traffic?

Which scenario would cause an ACL misconfiguration and deny all traffic? Apply an ACL that has all deny ACE statements. Having all ACEs with deny statements denies all traffic because there is an implicit deny any command at the end of every standard ACL.

Which statement is correct about a standard ACL?

Which statement about standard ACLs is true? Standard ACLS must be numbered and cannot be named. They should be placed as close to the destination as possible. They can filter based on source and destination address as well as on source and destination port.

Which two packet filters could a network administrator use on an IPv4 extended ACL?

Which two packet filters could a network administrator use on an IPv4 extended ACL? (Choose two.) Extended access lists commonly filter on source and destination IPv4 addresses and TCP or UDP port numbers. Additional filtering can be provided for protocol types.

What can be concluded after the commands are entered?

What can be concluded after the commands are entered? No traps are sent, because the notification-types argument was not specified yet. Traps are sent with the source IP address as 10.10.

What are the two types of ACLs in IPv4 choose two?

There are two types of IPv4 ACLs: Standard ACLs: These ACLs permit or deny packets based only on the source IPv4 address. Extended ACLs: These ACLs permit or deny packets based on the source IPv4 address and destination IPv4 address, protocol type, source and destination TCP or UDP ports, and more.

Add a comment